Jointing ladder W Type
The type C connection ladder serves to connect the type C ladder cable with its accessories in a straight position (180 degrees).
Material specifications:
Hot Rolled Coil / SPHC 1.8mm - 20 cm

 

Jointing ladder U Type
U type connection ladder serves to connect the U type ladder cable with its accessories in a straight position (180 degrees).
Material specifications:
Hot Rolled Coil / SPHC 1.8mm - 20 cm

 

Elbow Bracket
The elbow bracket is used as a place to place the cable ladder which is then tightened with 2 dynabolts to the vertical structure / wall, thus forming a cable ladder line that is side by side with the vertical structure / wall
Material specifications:
Hot Rolled Coil / SPHC 1.8mm - 5 cm wide

 

Mounting Bracket
The mounting bracket is used as a place to place the cable ladder which is then secured with 2 dynabolts to the horizontal / floor structure, thus forming a cable ladder line that is parallel to the horizontal / floor structure.
Material specifications:
Hot Rolled Coil / SPHC 1.8mm - 5 cm wide

 

Cover Clamp
Cover clamp is used to fasten / tighten the cover ladder to the cable ladder by using 2 cover clamps which are tightened with nuts.
Material specifications:
Hot Rolled Coil / SPHC 1.8mm - 5 cm wide

 

Cover Clamp
Cover clip is used to fasten / tighten the cover to the cable ladder by using 2 cover clips on both sides of the cable ladder (without screws). The cover clip is easier to install than the cover clamp, but it is easy to remove too, because the mounting mechanism does not use nuts.
Material specifications:
Hot Rolled Coil / SPHC 1.8mm - 5 cm wide

 

Stand Plate
The stand plate is used to secure the bar cable ladder in a horizontal plane so that the bar cable ladder stands vertically.
Material specifications:
Hot Rolled Coil / SPHC 1.8mm - 5 cm wide

 

Angle Connector
Angle connector serves to connect the cable ladder with its accessories in an elbow position (turn broken 90 degrees).
Material specifications:
Hot Rolled Coil / SPHC 1.8mm - 20 cm

 

Wall Bracket
The wall bracket functions to fasten the cable ladder to the vertical plane / wall directly, so that the cable ladder path is right in the vertical / wall plane.
Material specifications:
Hot Rolled Coil / SPHC 1.8mm - 5 cm wide

 

Hold Down Clamp
The hold down clamp functions to fasten the cable ladder to the hanger beam so that the cable ladder does not move.
Material specifications:
Hot Rolled Coil / SPHC 1.8mm

 

Jogled Plate
The jogled plate serves to connect 2 cable ladders with different heights (10 cm high by 5 cm high).
Material specifications:
Hot Rolled Coil / SPHC 1.8mm Length 20cm

 

End Plate
The end plate serves to cover the last part of a cable ladder line, so that it is closed and free of dirt / rodents.
Material specifications:
Hot Rolled Coil / SPHC 1.8mm Width 10cm

 

Adjustable Splice Plate
Adjustable splice plate functions to change the direction of the cable ladder path horizontally (turn left or right) with non-standard angles / requires adjustment to conditions in the field.
Used by attaching to the outside of the radius formed between 2 cable ladders.
Material specifications:
Hot Rolled Coil / SPHC 1.8mm Length 50cm

 

Horizontal Hinge Fish Plate
Horizontal hinge fish plate functions to change the direction of the cable ladder line horizontally (turn left or right) with a non-standard angle / requires adjustment to conditions in the field.
Used by attaching to the inside of the radius formed between 2 cable ladders.
Material specifications:
Hot Rolled Coil / SPHC 1.8mm Length 15cm x 2mm

 

Vertical Hinge Fish Plate
The vertical hinge fish plate functions to change the direction of the cable ladder line vertically (up or down) with a non-standard angle / requires adjustment to conditions in the field.
Used by attaching it to the side of the cable ladder, left and right.
Material specifications:
Hot Rolled Coil / SPHC 1.8mm Length 15cm x 2mm

 

Separator ladder
The separator ladder is used to separate lines / create separate paths in a (one) series of the same cable ladder. Usually the power cable / power cable is separated by a control cable / data cable.
Material specifications:
Hot Rolled Coil / SPHC 1.8mm Length 3000mm
Drop Out
The drop out serves to protect the cable insulation with the last part of a cable ladder path, so that the cable can come out of the cable ladder path safely / not in direct contact with the edge of the cable ladder.
Material specifications:
Hot Rolled Coil / SPHC 1.8mm Length 25cm